产品中心banner

news

Contact us

Enterprise Name: Jiashan Wang Machinery Co., Ltd.

Contact person: Manager Zhang 15921811816

                           General Wang 13806713135

                           Manager Sun(Guangxi)13657711598

Tel: 0573-84615806

Address:Zhejiang Company-No。 9, Lane 31, Jiashan, Zhejiang

             Guangxi Agency-No. 425, Chenxiong Mechatronic City, Nanning, Guangxi


Use in case of damage to sander caused by improper operation

Your current location: Home >> News >> Industry info

Use in case of damage to sander caused by improper operation

Date of release:2019-04-29 Author: Click:

Sanding machine is a precise production and processing machine, which should be strictly operated in accordance with the rules in order to prevent improper operation from causing damage to the whole set of woodworking machinery equipment, sanding machine and products.

1. Sanders need special operation to prevent non-professionals from making sanders.

2. Before starting the sander, check whether the voltage and air pressure are normal, whether there are impurities in the two machines, whether there is no defect in the three abrasive belts, whether the oil level of the four governors is normal, whether the screw of the fastening sand rack is tightened, whether the six infrared windows and reflectors are clean, whether the belt of the 7 sand photoelectric machine is tightened properly, whether the dust absorption is normal, and whether the 9 joints are connected. Whether the ground is excellent, 10 compressed air lubricant is satisfied.

3. The sander should be on time to refuel and lubricate the rotating and shaking parts.

4. The sander tightens the belt before operation and checks whether it is normal and the direction of the belt equipment is correct.

Fifth, switch on the main power supply and check whether the brake discs are separated. No suggestion of holding on.

Sixth, it is suggested that the main motor check whether the shaking of the sand rack is normal before the main motor. One by one, it is suggested that the main motor wait for the first main motor to work properly before recommending the second motor. It is suggested that the main motor should inquire about the shaking condition of the sand belt.

7. Measure the specification of workpiece with oil caliper before feeding, adjust the height of feeding belt according to the measured data before sanding. The sanding depth should not exceed 0.5 mm each time, and the width of sanding workpiece should not exceed 1 meter.

8. Sander can only sanding wood materials, workpieces can not contain metal, glass, sand and other consolidation sharp substances.

9. The sanding process should always pay attention to the operation of the machine. If there is any abnormality, it is necessary to stop and check. In emergency situations such as endangering personal safety, equipment safety, abrasive belt deviation and abrasive belt collapse, emergency brake switch should be used to stop the machine. No emergency brake switch should be used in normal operation.

10. Obstruct the operation of wearing gloves. Long-haired women need to wear hats and put their hair in them.

11. When operating the sander, the centrifugal force gathers and cannot be separated from the machine platform. When the machine is running, it can not touch the conveyor belt, obstruct the hands from inside the machine, and adjust the height of the sand frame when obstructing the operation.

12. When the operation is finished, it is necessary to shut down according to the correct procedure, clean up the dust in the machine table, close all the power supply and compressed air, and discharge the moisture in the oil-water separator of the air compressor and sander.


Improper operation of sander

The address of this article:http://en.wmffw.com/news/432.html

Key word:Operatingstepsofsander,Sander,SanderPrice

Recently browse:

木工冷压机

Address: No. 31, Lane 9, Taishan Road, Huimin Street, Jiashan County, Zhejiang Province

Tel: 0573-84615806

Contact person: Manager Zhang 15921811816

                           General Wang 13806713135

E-mail: 1592 1811816@163.com

Website Http: www.wmffw.com


Hot press manufacturer

Sweep, pay attention to us

  • Service
  • number
    15921811816
  • Message
  • web site
  • Online Service
    Please leave a message for us
    Please input the message here, and we will contact you as soon as possible.
    name
    Contacts
    Tel
    Telephone
    mailbox
    mailbox
    address
    address
    福利彩票北京赛车 秒速时时彩 秒速时时彩官网 北京赛车论坛 江苏快3走势 华盈彩票网 秒速时时彩官网 秒速时时彩 秒速时时彩 安徽快3